 |
|
| Put on the belt and bucket. |
|
|
Pulling the tape
through the Super Taper
into your bucket, keeping an eye on your tape to be sure you
have a consistent coverage of mud, (if the mud is skipping on
the tape, it is too thick). This Will Eliminate Blisters.
You may adjust the amount of mud applied to the tape by simply
adjusting the screw on the top of your Super
Taper.
|
 |
|
 |
Apply tape to walls and ceilings by pressing
the tape lightly with your fingers and pulling the tape tight
as you move forward. |
|
|
 |
Wipe your walls and ceilings with a 10"
knife. You may choose not to carry a bread pan due to the
fact that you have controlled the amount of mud you applied
by using the adjustment wing nut on the top of the taper.
Simply feather the mud into the bevel. |
|
 |
|
| Apply tape to all your upper
corners and 3 ways. Simply tear the tape and overlap ends. Run
tape down as far as you can reach. |
|
|
| Using a Corner Flusher or Combo Flusher Tool,
simply start about 6" out from the corner, press against
corner and glaze. To do your corner, press against corner and
glaze. To do your corners, back the flusher right into the corner
and pull out and down. DO NOT
PUSH INTO THE CORNER. This will eliminate the
need to pick. |
|
| |
- Made of flexible stainless steel
- Creases tape into corner in one
motion
- Feathers the cost of mud with one pass
- Will not pull tape off the floor or
out of corners
- No blades to break
- Does not pick up hitchhickers
- Goes over screw and nails without breaking
the head
|
|
|
 |
|
Corner
Flusher Handle. Also
available in extension model 2' to 31/2' - 3' to 51/2' -
4' to 71/2'
Lay your bottoms as you do your corners,
then place the Corner Flusher
or Combo Flusher right at the floor and
pull up. No Floors to Pick!
|
|
 |
|
| Using the Compound tube (Available
in 24", 36" or 48"). Attach the inside corner
applicator. Place in your mud, use your normal finishing mud
as you have been doing. Draw the mud into the tube by somply
pulling on the handle. Place the corner applicator on your angles
and with the wheels leading, simply press lightly on the handle
of the tube and apply your mud then glaze with 3" or larger
corner flusher. |
|
|
- Distributes mud evenly & easily
- Slides smoothly & accurately
- Durable
- No expensive parts
|
 |
|
| |
 |
- Easy to use
- Cleans up fast & easy
- Ideal for a variety of compounds
- Durable, no expensive parts
- Direct Draw refill
|
|
 |
Using the 3" or larger Corner Flusher,
finish your corners and bottoms the same as you did in your
first coat. Again no need to pick.
One Point: Some have found it advantageous
to do all your uppers first and once they are dry, go back
and do your drops. Because you are able to go fast this will
not hold you up.
If you choose to do both the upper and he
drops at the same time, first flush the uppers, then place
the flusher about 3" from the top and pull down to get
a clean corner. |
|
 |
You would do your nails and flats as you
always have.
|
|
If you are using paper bead you will want to
use our Outside Corner Applicator. As you did with
the inside applicator, draw mud into your compund Tube, then clip
on the outside application and apply to your outside corners. Then
place your corner bead straight or bull nose and using the Outside
Corner Roller, roll into place. Simple, Easy and Fast. Applicator
also available for 45° degree outside corners. |
|
- Easy to use
- Allows you to position corner bead as
you roll
|
|
- Easy to use
- Fast - efficient
- Can be used with straight & bull
nose bead.
|
|
 |
Close
this Window |
